Problems and influences in the pressure regulation process of gas pressure regulating equipment

Problems and influences in the pressure regulation process of gas pressure regulating equipment The gas pressure regulating equipment must involve the adjustment of the pressure before it is put into operation or during the maintenance process. The setting of the pressure parameters is reasonable and the operation is correct, which will affect the quality of the gas supply and the safety of the gas. The following describes the problems and impacts in the pressure regulation process of gas pressure regulating equipment.
1. Adjusting the operating pressure time selection: The gas non-uniformity is a characteristic of the city gas supply. The outlet pressure of the gas pressure regulator is affected by the flow rate. When the flow rate decreases, the outlet pressure increases; otherwise, the outlet pressure decreases. If the operating pressure is set when the gas consumption is small, once the gas peak occurs, the outlet pressure will decrease as the gas consumption increases. When the pressure is lower than the rated pressure of the gas appliance, the combustion temperature required by the process will not be reached. Therefore, the choice of adjusting the operating pressure time should be cautious.
2. The influence of objective factors on regulating operating pressure:
(1) The influence of geographical location height. The density of gas and air is different. If there is a difference in height at the beginning of the gas supply pipe, additional pressure will be generated. When the operating pressure is set too high, the pressure before the stove exceeds the allowable pressure of the cooker, which reduces the thermal efficiency of the burning appliance; if the adjustment is too low, the end pressure is insufficient and the combustion condition cannot be satisfied.
(2) The influence of the gas supply range. When gas flows in the pipeline, pressure loss and local resistance loss are generated. The larger the gas supply range, the farther the pipeline is laid, the more pipeline attachments, and the greater the pressure loss. Ignoring this factor during pressure setting may cause the pressure at the end of the supply pressure to fail to meet the combustion conditions.

(3) The influence of gas characteristics. The city gas supply targets are generally divided into residential gas, public building gas, industrial enterprise gas, and building heating, etc., and their respective gas consumption laws are different. For pure residential gas, the number of households supplied by the pressure regulator is large, and the possibility of maximum load at the same time for each cooker is small, the gas flow changes slowly, and the fluctuation of the outlet pressure is small. In addition, the type of burner used is different and the required supply pressure is also different. The appropriate operating pressure should be set according to the actual situation. (subsequent)

Source: Gas Regulator http://
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn

Aluminum oxide can be in continuous grinding to form new edges and is better than other abrasive grinding. Aluminum oxide cloth can be used for narrow belt, Flap Disc , and flap disc, for polishing pine wood, log board, furniture, handcraft products and vine products.

Abrasive Cloth is the cloth with grinding compound. According to the different grinding compound, the abrasive cloth can divided into four kinds: Aluminum Oxide Abrasive Cloth, Silicon Carbide Abrasive Cloth, Zirconium Oxide Abrasive Cloth and Calcined Aluminum Oxide Abrasive Cloth and so on. According to the hardness, it also can be divided into flexible abrasive cloth,middle flexible abrasive cloth and hard abrasive cloth. Some of them can do waterproof or oil-proof. The shape of the abrasive cloth is roll, belt and sheet. The abrasive cloth is generally used for wood grinding and metal grinding. It can available in vary grits. 

Aluminum Oxide Abrasive Cloth

After 30 years` development, abrasive cloth grinding has become a complete and self-contained system of new processing technology.  Because of its high processing efficiency, wide application range, strong adaptability, low cost, safe and convenient operation, it is well received by customers. In foreign countries, Abrasive Belt grinding technology has made great progress. It can be applianced for more and more processing object . It can process almost all engineering materials, from the general daily life appliance to application of large aerospace equipment.

If you have any questions, please contact with us directly. The abrasive cloth are produced with high quality and good appearance. Welcome you can visit our factory for inquiry. Please send mail directly to us.

Advantages of Aluminum oxide abrasive cloth:

High quality and low price, 

Available in vary grit.



Aluminum Oxide Abrasive Cloth

Aluminum Oxide Abrasive Cloth,Narrow Abrasive Abrasive Cloth,Cotton Abrasive Cloth,Soft Abrasive Cloth

Jiangsu Fengmang Compound Material Science & Tech Group CO.,LTD , http://www.fmabrasive.com