DELL floor three trees paint window paint TV decoration paint decoration ceiling fan light marble tile door closet door floor brick wall cabinet high-grade curtain bathroom tile bathroom door bathroom ceiling material bathroom door size bathroom size bathroom ceiling overall bathroom bathroom design bathroom floor tile bathroom leaking high-end Tile tile adhesive floor tile tile specification No Water Cooling Heating Furnace Heat Treatment Furnace, No Water Cooling Heating Furnace Tang Shan Jin Zhi Science & Technology Co.,Ltd. , http://www.jzgasifier.com
How to identify the quality of the home decorating project? It can be said that it is more difficult, especially the current decoration market is not very normative, but it is also the two sides of the A and B executives. As the home decorating is mainly manual operation, the technical level, construction period and construction season of construction workers will affect the actual project quality. Therefore, in terms of judging standards, there must be a certain degree of flexibility, do not over-indulgence, but it cannot be overemphasized. Too picky. In addition to the quality standards that can be clearly stated on the decoration contract, there are certain deviations that must be allowed in Other aspects, as long as it does not affect the overall structural safety, does not affect the specific use of functions, does not affect the appearance, even if it can be qualified. The following describes several methods for users to refer to, but to declare: This is not the standard issued by the state, does not have legal effects, but some of the views of some professionals, can not be used as the only criterion for the actual identification. 1. Ceiling and top brushing 1) Based on the design elevation of the ceiling, ±5mm is allowed on the horizontal plane. 2) The galvanized iron wire used for the hanging bar must not be smaller than No. 8 and the expansion bolt must be used as the hanging point. 3) If wooden keel is used, the material must be red and white pine without cracking or distortion. The specification of the main keel can not be less than 50mm x 70mm. 4) The paint must be painted on rollers, and the top surface must be flat and free from obvious potholes. 5) The cover panel of the bathroom shall not be made of gypsum board, mineral wool board, plywood, etc. which are easily deformed by moisture, and metal buckle boards or plastic boards shall be used. 6) The surface of the cover panel should be smooth, smooth, straight and evenly wide and narrow, with no missing edges, cracks and other defects. 7) The contact points of the cover panel, the keel and the dragon skeleton must be tightly connected, free from looseness, and be safe and reliable. 8) All wood keels must be coated with fire retardant paint. Wooden keels that are in direct contact with the wall or installed in the bathroom should be painted with antiseptic. Note: For the moment, the wooden keel is only used in a few high-end decoration and is not widely used in ordinary decoration. 2, tile, wallpaper, paint wall 1) The wall must be flat, smooth, people posted on the wall, flashlight by hand, generally do not have a serious refractive index is the formation of the standard, in addition, the yin and yang angle should be straight Founder. 2) The seams of wallpaper and wall cloth should be overlapped at the corner of the shade, and the corners of the corner should be compacted. No seams are allowed. 3) A good wallpaper or wall covering shall not contain bubbles, empty drums, cracks, curls, creases, and stains. 4) Wallpapers, wall coverings and hanging mirrors, door and window covers, curtain boxes, skirting boards, etc. must be immediately connected, and no gaps can be left. 5) The seams shall be horizontal and vertical, and the pattern and pattern of the joints shall be anastomosed, not separated from the seams, and not overlapped. The distance shall be more than one meter away from the wall surface, and obvious joints shall not be exposed. 6) The arrangement of non-complete bricks should be appropriate. The size of the bricks cut around the wall protrusions (such as sealing pipes, etc.) must be accurate and the edges must be consistent. 7) Tiles (face tiles) should be firmly affixed without hollowing or chromatic aberration, and should not be skewed, lacking corners, and edges and cracks. 8) The height of the joints can have a deviation of 5mm. In addition, the surface is flat and the vertical surface can also be allowed to deviate by 2mm. 3, plate floor and wooden floor 1) commonly used floor panel block: marble, granite, ceramic floor tiles, are using cement (mixed yellow sand, and some are also mixed with glue) paving, a large area of ​​ground material surface finish, texture , patterns, colors should remain uniform and consistent, no color. 2) The surface layer and the bottom layer must be completely adhered firmly, and no hollow sound can be knocked on. The seams are straight, the slits are even and full and firm. 3) The wooden keels (concrete joists), wool floors and underlays used for wooden flooring must be installed firmly, straight, and preferably coated with preservatives. 4) The hardwood surface should be nailed in the middle to the four sides. There should be an expansion gap of 5 to 10mm between the wooden floor and the surrounding wall, and it should be suppressed by the baseboard and the "foot of the horse" should not be exposed. 5) The wooden floor joints are tight and without any marks. The joints are staggered, the nails are firm, and there is no loose feeling when walking on the floor. There should be no sound. 6) The surface of the wooden floor should be polished smooth, no planing, no thorns, no scars, clear wood grain, smooth texture, uniform color. 4, wood products (cupboards, cabinets, wall panels, doors and windows sets, etc.) 1) hanging cabinets, cabinets, etc. to be installed firmly, no loose, no deformation, corners neat, no rough, door seal, open and flexible, no Falling, no rebound, in addition, can not leave a hammer mark, can not reveal the cap. 2) The difference between the upper and lower edges of various lines, curtain cases, upper frame of door and window cover, etc. shall not be greater than 2mm. The deviation of verticality shall also be within 2mm. The specific inspection can be checked with a line hammer. In brief: horizontal Vertical is the criterion. 3) The surface of the siding should be smooth and smooth. If the pattern is made, the width of the meticulous wood should be the same and close to the siding. In addition, there should be no hammer marks, no pollution, no nail caps, and edges and corners should be straight. 4) The joints of doors and windows, hanging mirrors, and curtain boxes should be tightly jointed. They must be docked at an angle of 45 degrees, and they should be close to the wall surface. There should be no gaps. 5) After the paint, there should be no leakage brush, sand, brush marks, stains and drop (tear) and so on. The surface is smooth and smooth. If you do clean water, the wood grain should be clear. If you mix water, the color must be bright and uniform. It is advisable to check the paint before it is used. The unqualified place should be rectified in time. The fine wood products have fine workmanship. Otherwise, it is difficult to find out some flaws after painting. (As the saying goes: paint is confused and paint is covered. Hundred ugly). 5, the water supply and drainage pipes, sanitary ware 1) The installation of the pipeline should also be horizontal and vertical, the pipeline is unobstructed, the installation position of various types of valves is reasonable, easy for future maintenance and replacement. 2) If it is used as a concealed pipe, water and pressure shall be used after completion to check if there are any seepage or water leakage in all joints, valves and connection points. 3) Sanitary fixtures need to be installed after the ceiling is suspended (if ceilings are required), the water supply and drainage pipes for baths, toilets, water tanks, and washbasins should be installed reasonably. Water and pressure must be carefully checked to check for leaks. In case of sloppyness, once a water leak occurs (generally directly affecting neighbors downstairs), the consequences can be disastrous (equivalent to renovating once). 4) Other utensils such as: mirror box, paper cylinder, soap jar, cup holder, towel bar, shower curtain rod, bathtub handle, etc. must be firmly installed (preferably with expansion bolt), no loosening phenomenon, suitable position and height, coating It is clean, non-destructive, and non-polluting. In addition, the faucet's cover must be close to the wall, and no gaps can be left. 6. Electrical wires (telephone lines, cable TV lines) and electrical installations 1) Dark lines shall be laid in sheathed pipes, preferably PVC flame-retardant pipes or metal pipes, and the joints of the wires shall be located in the terminal box (not to be simple With a pack of cloth, they are buried directly in the wall). 2) According to different uses of different specifications, types of wire, the telephone line should use a special sheath line (available from the telecommunications company, can not be used instead of conventional wires), cable TV cable using 75 ohm copper shielded cable, lighting line Lines with a cross-section of 1.5 square meters should be used, and air-conditioning lines should be at least 2.5 square meters. If there is a lot of high-power household appliances in a certain room, it is better to use a line with more than 4 square meters. 3) The power cord, telephone line and cable line must not be worn in the same jacket. Safety concealed sockets and concealed switches should be used. It is best to install a leakage protector. The heads of various types of junction boxes shall be reserved for more than 15 cm. Before the wall is closed, the power supply must be checked carefully. Telephone lines and cable television lines may be checked with a multimeter. 4) The hooks of large chandelier and ceiling fan are preferably made of steel bars larger than 8mm. They are embedded in the ceiling. The installation should be firm and the distance should not be less than 2.3 meters above the ground. 5) Fix the wall lamp and light pendant lamp with expansion bolts. The point of focus of the chandelier should be on the boom or chain, and must not allow the power cord to withstand the gravity of the chandelier. 6) The exhaust hood should be firmly installed in accordance with the instructions, and the height and inclination should be in accordance with the manufacturer's standards, and must not be changed at will or with ease. When laying cables and installing equipment, supervision and inspection should be carried out from time to time. Once buried in a wall or ceiling, it is difficult to check it. Especially for multiple switches, be sure to check whether they are effective or not, and if they do not meet the requirements, The construction party must be ordered to rectify.